View LTL5H3TBDS-032A_8934152.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL5H3TBDS-032A spec no.: ds20-2011-0172effective date: 09/01/2011revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * high luminous intensity output. * low power consumption. * high efficiency. * wide viewing angle major axis 1 1 0 / minor axis 45 * versatile mounting on p.c. board or panel. * i.c. compatible/low current requirements. pa ckage dimensions part no. lens source color ltl5h3 tb d s - 03 2 a blue diffused ingan blue notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. protruded resin under flange is 1.0 mm(.04") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice. 6. the led lamps use ltl5h3 tb d s part no. : ltl5h3 tb d s - 03 2 a page : 1 of 11 bns - od - c 131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 parameter maximum rating unit power dissipation 1 2 5 mw peak forward current (1/10 duty cycle, 10 ms pulse width) 100 ma dc forward current 3 5 ma derating linear from 2 5 0.6 ma/ reverse voltage 5 v operating temperature range - 3 0 c to + 8 5 c storage temperature range - 40 c to + 100 c lead soldering temperature [ 2.0 (.0 787 ") from body] 260 c for 5 seconds max. part no. : ltl5h3tbds - 032 a page : 2 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optica l characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous intensity i v 430 700 1210 mcd i f = 20ma note 1,5 viewing angle 2 1/2 110/45 deg note 2 (fig. 6 ) peak emission wavelength p 47 3 nm measurement @peak (fig.1) dominan t wavelength d 465 470 475 nm note 4 spectral line half - width ? 20 nm forward voltage v f 3. 0 4.0 v i f = 20ma reverse current i r 100 a v r = 5v capacitance c 40 pf v f = 0 , f = 1mhz note: 1. luminous intensity is measured w ith a light sensor and filter combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 5. iv guarantee must be included wi th 15% testing tolerance . part no. : ltl5h3tbds - 032 a page : 3 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : ltl 5h3tbds - 032 a page : 4 of 1 1 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * compatible with radial lead automatic insertion equipment. * most radial lead plastic lead lamps available packaged in tape and folding. * 2.54mm (0.1") straight lead spacing avail able. * folding packaging simplifies handling and testing. reel packaging is available by removing suffix a on option. package dimensions specification item symbol minimum maximum mm inch mm inch tape feed hole diameter d 3.8 0.149 4.2 0.165 component lead pitch f 2.3 0.091 3.0 0.118 front to rear deflection h -- -- 2.0 0.078 feed hole to bottom of component h1 20.0 0. 787 21.0 0.8 27 feed hole to overall component height h2 26.5 1. 043 28.1 1.1 06 lead length after comp onent height l w0 11.0 0.433 feed hole pitch p 12.4 0.488 13.0 0.511 lead location p1 4.4 0.173 5.8 0.228 center of component location p2 5.05 0.198 7.65 0.301 total tape thickness t -- -- 0.90 0.035 feed hole location w0 8.5 0.334 9.75 0.38 4 adhesive tape width w1 14.5 0.571 15.5 0.610 adhesive tape position w2 0 0 3.0 0.118 tape width w3 17.5 0.689 19.0 0.748 part no. : ltl5h3tbds - 032 a page : 5 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y packing spec total 2, 000pcs per inner carton 10 inner cartons per outer carton total 20000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing part no. : ltl5h3tbds - 032 a page : 6 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y bin table specification luminous intensity iv(mcd) i f @20ma bin code min. max. ns 430 600 nt 600 860 nu 860 1210 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @20ma bin code bin code bin code b08 46 5 470 b09 4 70 475 note: tolerance of each bin limit is 1nm part no. : ltl5h3tbds - 032 a page : 7 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y cau tions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteons sales in advance for information on application s in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety dev ices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 3 mm clearance from the base of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 300c max. 3 sec. max. (one time only) p re - heat pre - heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led . ir reflow is not suitable process for through hole type led lamp product. part no. : ltl5h3tbds - 032 a page : 8 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current - operated device. in order to ensure intensity unifor mity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model a circuit model b (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and mac hinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage a nd handing part no. : ltl5h3tbds - 032 a page : 9 of 11 bns - od - c131/a4 led led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y suggested checking list : training and certification 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certific ation dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. all surfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positio ned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conducti ve footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia - 471 labels on item or packaging? 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 3. no static charge generators (e.g. plastics) inside shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records com plete and on file? part no. : ltl5h3tbds - 032 a page : 10 of 11 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classification test item test condition reference standard endurance test operation life ta = 2 5 c if = 3 0 ma * test time= 1000 hrs ( - 24 hrs ,+72 hrs ) mil - std - 750d:1026 (1995) mil - std - 883d:1005 (1991) jis c 7021:b - 1 (1982) steady state operation life of high humidity heat ta = 6 0 c , rh= 90 % if = 20ma * test time= 50 0 hrs 2 hrs mil - std - 202f: 103b(1980) jis c 7021 : b - 11(1982) steady state operation life of low temperature ta = - 30 c if = 20ma * test time= 1000 hrs ( - 24 hrs ,+72 hrs ) high temperature storage ta= 1055 c * test time= 1000 hrs ( - 24 hrs ,+72 hrs ) mil - std - 883d:1008 (1991) jis c 7021:b - 10 (1982) low temperature storage ta= - 555 c * test time= 1000 hrs ( - 24 hrs ,+72 hrs ) jis c 7021:b - 12 (1982) environmental test temperature cycling 105 c 25 c - 55 c 25 c 30mins 5mins 30mins 5mins *test time: 10 0 cycles mil - std - 202f:107d (1980) m il - std - 750d:1051(1995) mil - std - 883d:1010 (1991) jis c 7021: a - 4(1982) thermal shock 105 5 c - 55 c 5 c 10mins 10mins *test time: 10 0 cycles mil - std - 202f:107d(1980) mil - std - 750d:1051(1995) mil - std - 883d:1011 (1991) solder resista nce t.sol = 260 c max. dwell time= 5sec . max. *test time: 1 time mil - std - 202f:210a(1980) mil - std - 750d:2031(1995) jis c 7021: a - 1(1982) solderability t. sol = 23 5 5 c dwell time= 5 1secs *test time: 1 time mil - std - 202f:208d(1980) mil - std - 750d:20 26(1995) mil - std - 883d:2003(1991) jis c 7021: a - 2(1982) 9. others the appearance and specifications of the product may be modified for improvement, without prior notice. part no. : ltl5h3tbds - 032 a page : 11 of 11 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL5H3TBDS-032A

	To Download LTL5H3TBDS-032A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .